Test & Measurement Applications
Variable DC Power Supplies for DC/DC Converter Testing
Sweep the converter input, establish startup conditions and evaluate performance under load. A controlled input source and a suitable output load let the same bench cover input-range checks, regulation and efficiency measurements.
View Recommended Power Supplies
What Does the Input Power Supply Do in DC/DC Converter Testing?
The variable source reproduces the converter input conditions. A separate electronic load sets output demand, allowing input-range, startup and efficiency tests at defined operating points.
Power path: variable DC source → converter input | converter output → electronic load.
Measurement: input voltage/current at the converter input and output voltage/current at its output. Instruments measure these points alongside the power path, not after the load.
The supply feeds the converter input; the electronic load draws from its output. Efficiency is output power divided by input power, using measurements taken at the defined test points.
What to Consider When Choosing a DC Power Supply for DC/DC Converter Testing
Input range and startup
Minimum/maximum input, undervoltage lockout, input capacitance and inrush current.
Power and load range
Input power including conversion losses, output load demand and continuous test duration.
Measurement and control
Voltage at DUT terminals, synchronized input/output readings, settling time and transient instrumentation.
Size from input power, not output power alone
A converter draws more input power than it delivers at its output. For an illustrative 240W output at 90% efficiency, input power is about 267W; at 24V this is about 11.1A before additional startup margin. Use the actual converter operating limits for selection.
What happens at low input voltage?
A regulated converter can demand more input current as its input falls. A source that is adequate at nominal voltage may enter current limit at the bottom of the sweep, changing the converter behavior you intended to measure.
Static sweeps or fast transients?
Programmable source steps suit repeatable input tests after settling. Fast line-transient and load-step characterization also requires the specified source/load dynamic response and appropriate oscilloscope measurements.
Compare Power Supplies for This Application
eTM-K6010SPL+ 60V 10A Programmable DC Power Supply
Low-voltage programmable input sweeps. 0–60V, 0–10A with stored settings and Modbus/SCPI for repeatable tests within this input-power envelope.
View Options & Buy Online
eTM-6050C 60V 50A 3000W Variable Bench DC Power Supply
Higher-current converter inputs. 0–60V, 0–50A, 3000W rated output with CV/CC, low ripple/noise and optional remote control for larger low-voltage converters.
View Options & Buy Online
eTM-12030C 120V 30A Variable Bench DC Power Supply
Wider input-voltage tests. 0–120V, 0–30A provides a wider sweep for converter families operating above a 60V input range.
View Options & Buy OnlineeTM-E150A 150W DC Electronic Load
Output loading up to 150W. CC, CV, CR and CP modes support output loading within the load’s operating envelope. The 150W limit applies even when voltage and current maxima are listed separately.
View Configuration & QuoteETOMMENS DC Power Supplies for DC/DC Converter Testing
Programmable voltage settings make input-range tests repeatable, while higher-current C-series models support larger low-voltage converters. Low ripple and noise, CV/CC operation and output switching provide practical bench control. Pair the input source with a suitably rated electronic load for output regulation and efficiency measurements.
ETOMMENS serves small and medium-sized businesses, large enterprises and multinational groups, with customers across North America—including the United States and Canada—Europe and the Middle East.
Our DC power supply range supports laboratory development, equipment testing and production applications, with technical support and customized solutions for different project requirements.
Where to Buy DC Power Supplies for DC/DC Converter Testing
You can buy ETOMMENS DC power supplies for DC/DC converter testing online at VariableDCPowerSupply.com. In-stock models dispatch within 1–3 business days after payment, with approximately 10 business days in transit. Free worldwide DDP shipping includes customs clearance, import duties and taxes.
Lead times for custom configurations are confirmed with the quotation.
Related: Electronic Loads. Explore the wider ETOMMENS variable DC power supply range.
Frequently Asked Questions
Do I need both a power supply and an electronic load?
For a typical DC/DC bench, the supply provides the input and the load draws controlled output current or power. They serve different roles.
Why does my converter fail to start on a bench supply?
Inrush, the selected current limit, lead drop or source dynamics may prevent the input from reaching the startup threshold. Compare voltage and current waveforms with the converter startup requirements.
Can supply display readings measure efficiency accurately?
They can help with setup. Efficiency measurements require suitable voltage/current accuracy and simultaneous or coordinated measurements at both input and output, accounting for cable losses.
Can E150A load a 150V output at 30A?
No. That would be 4500W. Its rated power is 150W, and valid operating points must also satisfy the applicable voltage/current range and minimum operating voltage.